"Postal Pete"
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
My local machine shop does a wonderful job with re-lining shoes.
The price is very reasonable and they were returned within a week.
I test fitted everything to check for shoe clearance, but it must be taken apart again to align the "leading shoes" as opposed to the "trailing shoes". (they must be in the proper order to work)
The photo shows the incorrect assembly (Springs are not in the correct holes).
John
The price is very reasonable and they were returned within a week.
I test fitted everything to check for shoe clearance, but it must be taken apart again to align the "leading shoes" as opposed to the "trailing shoes". (they must be in the proper order to work)
The photo shows the incorrect assembly (Springs are not in the correct holes).
John
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
After a long absence (sorry), I am back with some updates. I needed to locate a new Clutch housing shaft for the Kalmar because the original one had been cut.
I came across a problem when this was re-assembled....The bearing I normally use, would not work. The inside diameter was too large and purchasing a proper one was too expensive (they are selling for 98,00 Euro each in Holland).
The inside diameter on a SKF 6305 bearing (only cost 27,00 Euro) is 25mm, the shaft is 22mm.
The solution: A 22mm to 25mm Bronze Reducing Bushing!!
Now the new Bearing fits perfectly.
Finally I can get the Clutch assembly back on the motor...
The final bearing used is an SKF 6305-2RS1 (double rubber sealed).
98,00 Euro verses 27,00 Euro....which will you use??
Hans
I came across a problem when this was re-assembled....The bearing I normally use, would not work. The inside diameter was too large and purchasing a proper one was too expensive (they are selling for 98,00 Euro each in Holland).
The inside diameter on a SKF 6305 bearing (only cost 27,00 Euro) is 25mm, the shaft is 22mm.
The solution: A 22mm to 25mm Bronze Reducing Bushing!!
Now the new Bearing fits perfectly.
Finally I can get the Clutch assembly back on the motor...
The final bearing used is an SKF 6305-2RS1 (double rubber sealed).
98,00 Euro verses 27,00 Euro....which will you use??
Hans
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
Motor is almost ready to back in now.....I am VERY close.
John
John
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
Just a few more progress photos....
Test fitting the front panel so a lower grille could be installed properly.
Finished the 12 volt wiring and have bolted a 12 volt Voltage Regulator to the bulkhead panel. I will soon find out if this was accomplished correctly. First I need to wait for an exhaust pot (coming from DAFHobby) and do the wires on the Dashboard.
Since the weather is finally getting warm I decided to glue the rubber to my new windshield (Thanks again Ronny). Hopefully that will be installed this week.
John
Test fitting the front panel so a lower grille could be installed properly.
Finished the 12 volt wiring and have bolted a 12 volt Voltage Regulator to the bulkhead panel. I will soon find out if this was accomplished correctly. First I need to wait for an exhaust pot (coming from DAFHobby) and do the wires on the Dashboard.
Since the weather is finally getting warm I decided to glue the rubber to my new windshield (Thanks again Ronny). Hopefully that will be installed this week.
John
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
Does any have a good clear (and large) Electrical schematic for a type 1 Kalmar. I found one on Sverker's photo album page but it is so small it will not print properly.
I am desperate and need help because the wires have been so badly changed that I need to trace EVERY wire.
John
Någon gör har en bra tydliga (och stora) elektriska Principschema för en typ 1 Kalmar. Jag hittade en på Sverker's photo albumsida men det är så liten att det inte skrivs ut ordentligt.
Jag är desperat och behöver hjälp eftersom ledningarna har ändrats så illa att jag måste spåra varje tråd.
John
I am desperate and need help because the wires have been so badly changed that I need to trace EVERY wire.
John
Någon gör har en bra tydliga (och stora) elektriska Principschema för en typ 1 Kalmar. Jag hittade en på Sverker's photo albumsida men det är så liten att det inte skrivs ut ordentligt.
Jag är desperat och behöver hjälp eftersom ledningarna har ändrats så illa att jag måste spåra varje tråd.
John
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- HKC616
- Inlägg: 1664
- Blev medlem: 31 okt 2009 14:53
- Ort: Moheda
Re: "Postal Pete"
Namn: Fredrik Nilsson
Ägare till:
HKC616
CKJ666
DMO190 fd GMJ210
CNR370
DRW087
OHD14W fd DAZ225
CSJ294
50687 fd ELJ330
52091 fd DCC735
50012
Tidigare:
ALA167-såld
51800 fd DCC844-skrotad
51782 fd FHL739-skrotad
FRY181-såld
Ägare till:
HKC616
CKJ666
DMO190 fd GMJ210
CNR370
DRW087
OHD14W fd DAZ225
CSJ294
50687 fd ELJ330
52091 fd DCC735
50012
Tidigare:
ALA167-såld
51800 fd DCC844-skrotad
51782 fd FHL739-skrotad
FRY181-såld
- thebear54
- Inlägg: 82
- Blev medlem: 26 nov 2011 00:59
- Ort: Mount Tabor, Vermont U.S.A.
- Kontakt:
Re: "Postal Pete"
Thanks Fredrik....That helps somewhat because it is a type 2 schematic. At least I could expand the schematic to build a larger one.
One question: How does this word translate to english: branslematare
Hans (John)
One question: How does this word translate to english: branslematare
Hans (John)
Director DAF Club of America
Director DAF Museum USA
Director DAF Museum USA
- HKC616
- Inlägg: 1664
- Blev medlem: 31 okt 2009 14:53
- Ort: Moheda
Re: "Postal Pete"
28 Bränslemätare = Fuel gauge. I think that is it the sensor in the gas tank, but im not sure.
/Fredrik
/Fredrik
Namn: Fredrik Nilsson
Ägare till:
HKC616
CKJ666
DMO190 fd GMJ210
CNR370
DRW087
OHD14W fd DAZ225
CSJ294
50687 fd ELJ330
52091 fd DCC735
50012
Tidigare:
ALA167-såld
51800 fd DCC844-skrotad
51782 fd FHL739-skrotad
FRY181-såld
Ägare till:
HKC616
CKJ666
DMO190 fd GMJ210
CNR370
DRW087
OHD14W fd DAZ225
CSJ294
50687 fd ELJ330
52091 fd DCC735
50012
Tidigare:
ALA167-såld
51800 fd DCC844-skrotad
51782 fd FHL739-skrotad
FRY181-såld